Ring Screw Torque On An Ultradot?

Brought to you by Zero Bullet Company Inc.

Moderators: pilkguns, m1963, Isabel1130

Post Reply
big mouse
Posts: 37
Joined: Sun Oct 28, 2012 1:36 pm

Ring Screw Torque On An Ultradot?

Post by big mouse »

I will be using a new set of Leupold Rifleman Detachable Rings to mount an Ultradot onto a .22 caliber pistol.

The rings are 1" in diameter, horizontally split and made of aluminum in a Weaver pattern. Each ring top is secured

with 2 screws. The tech at Leupold stated that 22 in-lbs. of torque was the maximum recommended amount to use.

Being unfamiliar with Ultradots, he was reluctant to say if this amount was okay to use on this brand of sight.

Have any of you ever used a torque screwdriver when tightening the ring top screws? If so, what amount worked

for you? I don't want to accidentally over do it and end up crushing my Ultradot's tubes.
Last edited by big mouse on Fri Jul 15, 2016 7:28 pm, edited 2 times in total.
Rover
Posts: 6986
Joined: Sat Nov 15, 2008 4:20 pm
Location: Idaho panhandle

Re: Ring Torque On An Ultradot?

Post by Rover »

If you're biting your tongue, you're putting it on too tight.

Just put it on firmly, with a little electrical tape in the rings and you'll be fine.
big mouse
Posts: 37
Joined: Sun Oct 28, 2012 1:36 pm

Re: Ring Torque On An Ultradot?

Post by big mouse »

Rover,

I do appreciate your suggestion; will give it a try. Have a few more questions. Should I put that tape

only the ring bottoms? Only on the tops? Or is it best to apply it on both surfaces of both the front

and rear rings? Thanks!
Rover
Posts: 6986
Joined: Sat Nov 15, 2008 4:20 pm
Location: Idaho panhandle

Re: Ring Torque On An Ultradot?

Post by Rover »

I would put the tape on front and rear bottom rings, covering about 90 degrees of the circle.

This will keep the scope from slipping from the recoil.

It really isn't that big a deal.
C. Perkins
Posts: 480
Joined: Fri Aug 21, 2009 9:31 pm
Location: Was a Bullseye Master

Re: Ring Torque On An Ultradot?

Post by C. Perkins »

Little known secret with using the "L" shaped allen and torx bit keys.
Finger tight is using the long end into the screw with your fingers on the "L" section.

Putting the "L" section into the screw and pulling on the long end until it "torsions" is just about the proper torque.
Make sure there is a gap in between the ring halves when torqued.

As far as using gooey electrical tape, DO NOT USE IT.
There is never any need to put anything in between the scope and inner rings unless something is not right, and if something is not right, then fix it, but not with adding TAPE.

My goodness Roger; I really wonder if you are really here to help or send people down the wrong path.
Must be the Arizona sun; glad I got out of there.
D.R. badge #99
Rover
Posts: 6986
Joined: Sat Nov 15, 2008 4:20 pm
Location: Idaho panhandle

Re: Ring Torque On An Ultradot?

Post by Rover »

Obviously, you haven't been using crap mounts, Snowbird.
C. Perkins
Posts: 480
Joined: Fri Aug 21, 2009 9:31 pm
Location: Was a Bullseye Master

Re: Ring Torque On An Ultradot?

Post by C. Perkins »

Rover wrote:Obviously, you haven't been using crap mounts, Snowbird.
I knew that would get a rise out of you :)
If I had your money I would be a snowbird.
big mouse
Posts: 37
Joined: Sun Oct 28, 2012 1:36 pm

Re: Ring Torque On An Ultradot?

Post by big mouse »

[quote="Rover"]Obviously, you haven't been using crap mounts, Snowbird.[/quote]


Rover,

Are you saying that Leupold Rifleman Detachable Rings are crap mounts?

If there is some other product of a similar design that's better, please fill me in.

By the way, what rings are you using? Thank you.
Rover
Posts: 6986
Joined: Sat Nov 15, 2008 4:20 pm
Location: Idaho panhandle

Re: Ring Torque On An Ultradot?

Post by Rover »

I don't know whether the Leupold rings are any good or not.

I'm using crap rings I had laying around in my junk box.

Good rings or not, the tape works.
Bullseye26
Posts: 8
Joined: Tue Dec 16, 2008 2:56 am

Re: Ring Screw Torque On An Ultradot?

Post by Bullseye26 »

Leupold Rifleman rings are excellent and at a very cheap price. Been using them for years on my 1911 slide mount wad guns. No issues. Very convenient as you can detach and reattach without loosing zero. Degrease with solvent and use Leupold's 22 inch pound or snug tight. No need for tape. They are very strong and will crush the tube if you get carried away.
Post Reply